Hi All
Here is the detail for different type of handovers in 3G.
UMTS Handover
There are following categories of handover (also referred to as handoff):
• Hard Handover
Hard handover means that all the old radio links in the UE are removed before the new radio links are established. Hard handover can be seamless or non-seamless. Seamless hard handover means that the handover is not perceptible to the user. In practice a handover that requires a change of the carrier frequency (inter-frequency handover) is always performed as hard handover.
• Soft Handover
Soft handover means that the radio links are added and removed in a way that the UE always keeps at least one radio link to the UTRAN. Soft handover is performed by means of macro diversity, which refers to the condition that several radio links are active at the same time. Normally soft handover can be used when cells operated on the same frequency are changed.
• Softer handover
Softer handover is a special case of soft handover where the radio links that are added and removed belong to the same Node B (i.e. the site of co-located base stations from which several sector-cells are served. In softer handover, macro diversity with maximum ratio combining can be performed in the Node B, whereas generally in soft handover on the downlink, macro diversity with selection combining is applied.
Generally we can distinguish between intra-cell handover and inter-cell handover. For UMTS the following types of handover are specified:
• Handover 3G -3G (i.e. between UMTS and other 3G systems)
• FDD soft/softer handover
• FDD inter-frequency hard handover
• FDD/TDD handover (change of cell)
• TDD/FDD handover (change of cell)
• TDD/TDD handover
• Handover 3G - 2G (e.g. handover to GSM)
• Handover 2G - 3G (e.g. handover from GSM)
The most obvious cause for performing a handover is that due to its movement a user can be served in another cell more efficiently (like less power emission, less interference). It may however also be performed for other reasons such as system load control.
• Active Set is defined as the set of Node-Bs the UE is simultaneously connected to (i.e., the UTRA cells currently assigning a downlink DPCH to the UE constitute the active set).
• Cells, which are not included in the active set, but are included in the CELL_INFO_LIST belong to the Monitored Set.
• Cells detected by the UE, which are neither in the CELL_INFO_LIST nor in the active set belong to the Detected Set. Reporting of measurements of the detected set is only applicable to intra-frequency measurements made by UEs in CELL_DCH state.
The different types of air interface measurements are:
• Intra-frequency measurements: measurements on downlink physical channels at the same frequency as the active set. A measurement object corresponds to one cell.
• Inter-frequency measurements: measurements on downlink physical channels at frequencies that differ from the frequency of the active set. A measurement object corresponds to one cell.
• Inter-RAT measurements: measurements on downlink physical channels belonging to another radio access technology than UTRAN, e.g. GSM. A measurement object corresponds to one cell.
• Traffic volume measurements: measurements on uplink traffic volume. A measurement object corresponds to one cell.
• Quality measurements: Measurements of downlink quality parameters, e.g. downlink transport block error rate. A measurement object corresponds to one transport channel in case of BLER. A measurement object corresponds to one timeslot in case of SIR (TDD only).
• UE-internal measurements: Measurements of UE transmission power and UE received
signal level.
• UE positioning measurements: Measurements of UE position. The UE supports a number of measurements running in parallel. The UE also supports that each measurement is controlled and reported independently of every other measurement.
Keep checking for new posts till then Happy Reading.
Warm Regards
Kushal Mahajan
Subscribe to:
Post Comments (Atom)
Hi Kushal,
ReplyDeleteThis is a good article. I would like to add something, as per my knowledge:
1. UMTS 3G has soft-softer handoff also. It means, in the active set, at list two members (sectors) belongs to same Node B and at least one member (sector) belongs to different NodeB.
2. Do you mean CELL_INFO_LIST is same as Neighbor list? Neighbor list is configured for each sector. The sector broadcast this list and instruct UE to monitor these pilots (SC Scrambling Code) However, UE may report some pilots / SC, which do not belongs to Neighbor list. Operator collects such measurement reports from UE and reconfigure neighbor list t make sure.
3. We have candidate list also in UE measurement report.
4. In IS-95 we had two algorithms for Soft handoff. For softhandoff A case, the co-efficients were constant to decide ADD pilot and DROP pilot to candidate (or active set). While for softhandoff B algorithm, such co-efficients were dynamic, and calculated by UE.
Hi Manish
ReplyDeleteThanks for sharing knowladge with us.
i already discussed about soft & softer handover in the above article & would like to share that a mobile can latch into 3 active cells at a time & choose the one for handover which provide the max. signal strength.